From hand-carved lures to CNC-cut Paulownia.

Lure Builder is for small lure makers ready to take the next step. Turn a lure you make by hand into an accurate CAD model, check how it will float, then export matched halves to cut from Paulownia on your CNC router, or a pair to 3D print. Every lure after the first comes out the same.

Move the ballast

Rests about 28° tail-down, ready to walk the dog.

Same body, three ballast positions. In the editor the angle comes from your own design: timber, coating, wire, hooks and ballast.

Make it once. Cut it every time.

A lure carved by hand is hard to make twice. As a design file it comes off the machine the same shape, weight and rest angle every time, so a good one can become a run.

  • Trace a lure you already make

    Photograph its side and top, set the scale from its measured length, and auto-trace fits the curves to the silhouette.

  • Or start from a preset

    GT stickbaits, poppers, pencil poppers and small walkers, then shape it with sliders or every control point.

  • Keep it as a file

    Save the design and reopen it for the next batch. Resize it and the wire, hooks, rings and ballast are re-chosen to suit.

Cut from Paulownia on your CNC router

Both halves are nested mirror-image on one Paulownia blank and cut in two operations, so they come off the machine as a matched pair. Lure Builder lays out the blank, tabs and flip registration for you, and checks the design against your tools: a wire groove no narrower than your smallest ball-nose bit, a popper cup your finishing bit can reach, and no tail or nose too thin for soft timber.

  1. Glue-face pass

    Cut the wire groove, hanger and ballast pockets and registration holes into the flat face of both halves.

  2. Flip

    Turn the blank over onto dowel pins so the second side lines up with the first.

  3. Shape pass

    Rough, then finish the outside of each half with a ball-nose bit, leaving tabs to the frame.

  4. Release and glue

    Cut the tabs, fit the through-wire, hangers and ballast, and glue the halves together.

  5. Finish

    Sand, seal and coat. The float check already counted the coating.

What you export

Shape-pass STL
Both half-bodies nested mirror-image on the blank, with tabs and frame, for your 3D toolpaths.
Glue-face DXF, SVG and PDF
The wire groove, pockets and registration holes as flat geometry.
Setup sheet
Blank size, tools, flip steps, ballast sizes and the glue-up.

The files go into the CAM software you already use, so you keep your own feeds, speeds and machine.

Why Paulownia

Paulownia weighs about a quarter as much as sea water and machines cleanly, so it makes buoyant surface lures that are quick to cut and light to cast. A sinking lure needs most of its weight in ballast, and the app sizes that for you. Weigh a block of your own stock and enter its density, and the float check uses that number.

Balsa150Paulownia280Cedar370Basswood415Sea water 1025
Density in kg/m³. A lure floats while its overall density stays under the water line.

I'm a CNC machinist and a keen fisherman. What brought me to lure making is the idea of making something, then catching a fish on it.

Alastair Pilley, Paulownia Timber Supplies, Sydney

Or 3D print it

The same design exports as a print-ready pair of halves, so you can prototype on a printer before you cut timber, or make the whole run printed.

  • Each half prints glue-face down, with no supports.
  • Clearances for the wire channel and registration pins are set to suit your printer.
  • PETG or ASA stand up to salt water and sun better than PLA.
  • The float check uses your print material and how solid the print is. Test a printed lure in water before you trust its angle.